Share:


PU Coating Anti Slip

DESCRIPTION
DURAPOL 500 Anti Slip(Car Park) is a high performance, two components pigmented polyester urethane coating which offer anti slip properties.
USES Design as a finishing coat to resist chemical, ultra violet and abrasion. Suitable  concrete surfaces where chemical resistance and weather ability are required. A protective and decorative top coat for concrete floors.

BENEFITS
• Attractive - Outstanding gloss and colour retention.
• Versatile - May be applied over most primed substrate. Ultimate  in  protection and decorative.
•  Performance - Unmatched performance by other similar generic type product.
• Compliance  - BS 476 Part 5,6 & 7 for Class '2' fire rating.
• Hard wearing - Recommended for use in vandal/graffiti prone areas.
• Offer slip resistance perfoman.

COLORS
Available in wide range of colors.

FINISH
Gloss, Satin, Matt

SPECIFICATION
DURAPOL 500 Anti Slip (Car Park)  is suitable for use on awide range of substrate with varying service requirements. Specific recommendation, can be obtained upon request.

APPLICATION PRODUCER
SURFACE PREPARATION

DURAPOL 500 Anti Slip (Car Park) shall be applied over clean, dry recommended primer or tie coat.
Mixing Stir each component separately using a high power  (750rpm) electric drill fitted with a paint mixer or a wing type mixing paddle. Then pour the entire content of  Part B into Part A and continue to mix for 2-3 minutes before use. Do not mix more than the required amount within the stipulated pot life.

Thinning
No thinnig required.

Method Of Application
Apply evenly the entire surface using either brush, roller, air less or conventional spray.

Recoating
Touch Dry : 6 hrs. at 25ºC
Maximum Recoating Time : 24hrs. at 25ºC
Minimum Recoating Time : 14hrs. at 25ºC

NOTE :
For best results when spraying, moisture trap should be installed at air inlets to the spray pot to avoid coating contamination. As the Part B is highly sensitive to moisture, it is advis able to use entire content once opened.

HEALTH & SAFETY
This product is highly combustible and contains free isocyanates; use approved respirator during application and provide adequate ventilation. No smoking is allowed. For further information, refer to the product Material Safety Data Sheet, available upon request.

FURTHER INFORMATION
With a wealth of technical and practical experience built up over many years in our pursuit of excellence especially in the protective, flooring and concrete technology, make ETEPOX your patner today!

What is PU Coating Anti Slip?
 

PU coating anti-slip refers to a polyurethane-based coating that is formulated to provide a slip-resistant surface. It is designed to enhance safety in areas where slip and fall accidents may occur, such as ramps, walkways, stairs, or floors that are exposed to water, oil, or other slippery substances.

Here are some key features and benefits of PU coating anti-slip:

  1. Slip Resistance: PU coating anti-slip incorporates additives or textures that increase friction and improve traction on the coated surface. This helps to reduce the risk of slips and falls, even in wet or oily conditions.

  2. Durable Protection: The polyurethane-based formulation of the coating provides durability and protection for the underlying substrate. It creates a tough, resilient barrier that resists wear, abrasion, and impact.

  3. Chemical Resistance: PU coating anti-slip is often formulated to have good resistance against chemicals, oils, and other substances that could potentially degrade the coating or compromise its slip-resistant properties.

  4. Easy Maintenance: The coating typically has a smooth, non-porous surface that is easy to clean and maintain. It resists the accumulation of dirt, grime, and contaminants, making it suitable for environments where cleanliness is important.

  5. Versatility: PU coating anti-slip can be applied to various substrates, including concrete, metal, wood, and certain plastics. It can be used in different industries and applications, such as industrial facilities, commercial buildings, public spaces, and residential areas.

It's important to note that the slip resistance of the coating may vary depending on the specific formulation and the texture or additives used. It's recommended to consult with the manufacturer or supplier of the PU coating anti-slip product for detailed information on its slip resistance ratings, application guidelines, and maintenance recommendations.

Proper surface preparation, including cleaning and ensuring a suitable substrate, is crucial for the successful application of the coating. Professional installation or guidance may be recommended to ensure optimal results and long-term performance.

Overall, PU coating anti-slip offers a combination of slip resistance, durability, chemical resistance, and easy maintenance, making it a valuable solution for creating safer surfaces in areas prone to slips and falls.



 Inquiry - PU Coating Anti Slip